Common Specifications

Beta Marine has extensive experience from over twenty years of manufacturing marine bespoke generating sets for a broad spectrum of marine applications; From narrowboats, wide beams, dutch barges, sailing yachts, super yachts, to commercial fishing boats, trawlers, tugs, passenger ferries, cargo boats & fast patrol boats. These bespoke generating sets has resulted in the development of a standard base range of marine generating sets from 4kVA < 58kVA.

The BetaSet / Genset 40T is available as standard as:

• 4 Pole 50Hz Standard voltage is 230v Single Phase – 400v 3 Phase @ 1,500 rpm.
• 4 Pole 60Hz Standard voltage is 127/254v Single Phase – 440v 3 Phase @ 1,800 rpm.

All are available with either Heat Exchanger, Keel or Radiator Cooling.

We can supply most electrical voltages and frequencies between 120 volt single phase to 415 volt 3 phase, additionally we can also build to bespoke individual specifications.

Emissions

• The BetaSet/BetaGen 40T is only Stage II compliant and cannot be used on European canals, rivers nor the Rhine (CCNR), irrespective of the application. Otherwise it can be used in all unregulated applications/territories.

• For EPA compliance, all sets must be specially quoted for.

Common Standard Specification

• Beta Marine water cooled ‘Kubota’ based diesel engine, turbocharged, mechanically governed as specified above for operation in accordance with ISO 3046* for marine diesel generating sets.

• Heat exchanger cooling complete with cupro-nickel tube bundle and phosphor bronze end caps, sacrificial anode, fresh water and sea water pumps. Water cooled exhaust manifold, water injection exhaust bend, sump drain pump, fuel, oil, and air filtration. CE approved fuel supply & return flexible connection hoses or

• Keel cooled header tank & water cooled exhaust manifold, fresh water pump, dry exhaust outlet including exhaust elbow & flexible stainless steel bellows, sump drain pump, fuel, oil, and air filtration. CE approved fuel supply & return flexible connection hoses.

• 12 volt electric start system with 70 Amp battery charging insulated return alternator and stop solenoid valve.

• A combined start/stop, alarm and protection module is supplied loose with 3 metres of connection cable. The module includes: engine start and stop push buttons, an hours run meter and indicators with shutdown on fault for either low lubricating oil pressure or high coolant temperature. On insulated system push buttons are replaced with a key switch and separate hour counter is supplied.

• The Mecc Alte marine rated “generator” operates at 0.8pf and has a ventilated drip proof enclosure with IP 22 protection & single bearing construction. The generator is self-regulating, self-excited and is complete with terminal box and automatic voltage regulator. Suitable for operation in engine room temperatures of up to 45⁰C.

• Engine and generator are close coupled together and mounted on substantial steel feet with marine failsafe anti-vibration mountings to isolate the set from the vessels seating.

• Paint: The generating set is painted Beta Red for heat exchanger or Dark Brunswick Green for Keel cooled engines, the acoustic enclosures are off-white.

• Each generating set is “full load” tested in accordance with our quality document QA023.

• Tri-wall packed on a wooden base.

• Warranty: 12 months from date of commissioning or 18 months from date of despatch – whichever comes first and subject to the Warranty Terms and Conditions, section 17 within our General Terms and Conditions of Sale.
  

*For operation in ambient temperature of 45⁰C the output will be de-rated by 8%. Please contact Beta Marine for further information.

BetaGen Additional Specification

Although our generating sets are quiet by comparison as standard, for customers or installations that demand especially quiet operation, Beta Marine have developed a highly insulated acoustic enclosure option. These enclosures reduce noise level down to a low 60 dB(A) when measured at seven metres under free field conditions at normal operating speed.

Manufactured from ‘zintec’ steel and finished in off white ‘powder coated’ paint to complement our engine colour, the panel frame is bolted together for rigidity & strength and is lined with high quality 38mm flame retardant acoustic foam material (including a 4mm polymeric barrier), held in place with high temperature silicon adhesive.

Quick release “service” panels facilitate easy, simple and unobstructed access to the engine, alternator and ancillaries. Acoustic attenuating ducts provide air flow in and out of enclosure assisted by a ventilation fan.

The design allows the engine and alternator unit to rest on flexible mountings within the enclosure and all necessary connections including speed control cable, battery +ve and -ve terminals, fuel inlet and return, cooling water inlet and return, calorifier feed and return (if specified), wet or dry exhaust outlet are all brought out of the enclosure – ready for a quick and easy installation.

4 – Pole (1,500 rpm) 220/230/240v 50Hz – 1 Phase Specifications / Data

Set / Model	Max. Output	Prime Output @ 1,500 rpm 0.8PF	Typical Load*	Engine Model	Cubic Capacity	Number of Cylinders	Fuel @ Prime Output
BetaSet / BetaGen 40T	38.0 kVA	34.5 kVA	132.0 A	BV3800 TBG	3769 cc	4	9.3 Lt/Hr

*Typical Maximum Amps at 230v Based on kW Electrical Load

4 – Pole (1,500 rpm) 380/400/415v 50Hz – 3 Phase Specifications / Data

Set / Model	Max. Output	Prime Output @ 1,500 rpm 0.8PF	Typical Load*	Engine Model	Cubic Capacity	Number of Cylinders	Fuel @ Prime Output
BetaSet / BetaGen 40T	42.0 kVA	38.2 kVA	46.7 A	BV3800 TBG	3769 cc	4	9.2 Lt/Hr

*Typical Maximum Amps at 415v Based on kW Electrical Load

All kVA Prime Output Ratings are Marine Class F Temperature Rises.

Emissions

• The BetaSet/BetaGen 40T is only Stage II compliant and cannot be used on European canals, rivers nor the Rhine (CCNR), irrespective of the application. Otherwise it can be used in all unregulated applications/territories.
• For EPA compliance, all sets must be specially quoted for.

4 – Pole (1,800 rpm) 127/254v 60Hz – 1 Phase Specifications / Data

Set / Model	Max. Output	Prime Output @ 1,800 rpm 0.8PF	Typical Load*	Engine Model	Cubic Capacity	Number of Cylinders	Fuel @ Prime Output
BetaSet / BetaGen 40T	46.0 kVA	41.9 kVA	145.0 A	BV3800 TBG	3769 cc	4	9.2 Lt/Hr

*Typical Maximum Amps at 254v Based on kW Electrical Load

4 – Pole (1,800 rpm) 440v 60Hz – 3 Phase Specifications / Data

Set / Model	Max. Output	Prime Output @ 1,800 rpm 0.8PF	Typical Load*	Engine Model	Cubic Capacity	Number of Cylinders	Fuel @ Prime Output
BetaSet / BetaGen 40T	56.0 kVA	51.0 kVA	58.8 A	BV3800 TBG	3769 cc	4	9.4 Lt/Hr

*Typical Maximum Amps at 440v Based on kW Electrical Load

All kVA Prime Output Ratings are Marine Class F Temperature Rises.

Emissions

• The BetaSet/BetaGen 40T is only Stage II compliant and cannot be used on European canals, rivers nor the Rhine (CCNR), irrespective of the application. Otherwise it can be used in all unregulated applications/territories.
• For EPA compliance, all sets must be specially quoted for.

Dimensions & Weights

BetaSet 40T

	A	B	C	Weight
BetaSet 40T	146cm	67cm	86cm	735kg

BetaGen 40T

	A	B	C	Weight
BetaGen 40T	180cm	74cm	91cm	950kg

Image is for illustrational purposes and not necessarily representative.

Control Module Options

Beta Marine offer a range of control modules to cater for various requirements. Click on any of the thumbnail images to view a larger more detailed image of the control module. Find out more…

Engine Electrical Options

We offer a selection of standard engine alternator options (subject to additional cost) however, if you require an alternative solution with specific engine alternators we can usually design, manufacture and fit suitable alternator supports and pulley drives to suit your needs. For further information please contact a generating set specialist on the Beta Marine Help Desk.

Note: Minimum recommended battery: Not included.

12v 180Ah 1050CCA

12 Volt Alternators
70 Amp, 12 Volt Insulated Return Alternator	Standard

24 Volt Alternators
55 Amp, 24 Volt Electric Start & Alternator	Optional

Forward End Alternator Guard

Image is for illustrational purposes and not necessarily representative and will vary by generating set selection and customer requirements.

Optional for all BetaSet/BetaGen models.

Double Walled Fuel Injection Pipes & Alarm

Double walled (sheathed) fuel injection pipes, in the event of an engine fuel injection inner pipe failure, fuel is leaked into the outer pipe which then feeds back to the fuel tank via a float chamber which activates an engine alarm.

Optional for 4 Pole BetaSet – BetaGen 21, 26 & 33.

Accessories

Beta Marine generating sets are complemented by a complete range of installation accessories. Find out more…

Literature & Manuals

ECO-ECP Alternator
Operators Maintenance Manual

Dealer Locator

When ordering an engine we always recommend that you talk to your local Beta Marine Dealer / Distributor about what you are looking for, so that you can agree a specification of the engine and accessories you require and they will then quote you. If you don’t have a local dealer then you or your installation engineer can contact the Beta Marine Help Desk.

International Distributors

When ordering an engine we always recommend that you talk to your local Beta Marine Dealer / Distributor about what you are looking for, so that you can agree a specification of the engine and accessories you require and they will then quote you. If you don’t have a local dealer then you or your installation engineer can contact the Beta Marine Help Desk.

Online Enquiry Form

If you are human, leave this field blank.

Your Name *

Company

(If Applicable)

Contact Phone *

Address

Contact Email *

Country *

Confirm Email *

Is the Vessel *

New

Existing

Please Specify Application

Power Output Required *

kVA

kW Electrical

Power Output Required

Type of Engine Required *

Heat Exchanger Cooled

Keel Cooled

Radiator Cooled

Electrical Output Voltage Required *

Electrical Output Freqency Required *

Electrical Output Phase Required *

Please Advise

When Do You Require Delivery of the Generating Set?

Where Do You Require Delivery of the Generating Set?

Enquiry or Comments

When using the contact form or an email address within this website you will be providing Beta Marine Ltd some very limited personal information. This information is used only in the scope of performance of contract or fulfilment of the requested service such as processing your enquiry or providing bespoke technical support.

After completion of the performance of contract or fulfilment of the requested service the personal data you have provided is first securely stored for future reference and or further support. After a period of 24 months the data you have provided is securely deleted.

All forms and emails are delivered by a Hypertext Transfer Protocol Secure HTTPS method.

Submit

*

reCAPTCHA is required.